Showing 1–20 of 23 results

Attachments and implements for farm tractors. Includiing bale stabbers, bale grappers, box blades, post hole diggers, edgers, ditchers and post drivers. Equipmentland manufacturers offer other implements not necessarily displayed on Equipmentland.com, so feel fee to call us or email us to inquire about other implements.

Product Listings

POSTMASTER POST POUNDER
– Includes Hydraulic Tilt up to 19 degrees each direction.
– 56 inch stroke; up to 60 strokes per minute.
– For 3 inch to 8 inch wood or steel posts.
– Standard 6 inch round head collar.
– Hydraulic drop hammer design
– 988 lbs
$13,553.00
POSTMASTER DRIVER POST POUNDER
– 56 inch stroke; up to 60 strokes per minute.
– For 3 inch to 8 inch wood or steel posts.
– Standard 6 inch round head collar.
– Hydraulic drop hammer design, does not operate with hydraulic cylinders, springs, or return lines.
– Includes hoses and couplers.
– 988lbs
$10,393.00
– Hydraulic Tilt up to 19 degrees each direction.
– 36 inch stroke; up to 60 strokes per minute.
– For 3 inch to 8 inch wood or steel posts.
– Standard 6 inch round head collar.
– Hydraulic drop hammer design
– 1012 lbs
$10,193.00
– Center cut, Offset Left or Right Hand
– Category 2-3 Mount
– Banded Belt Drive, cuts 12″ Deep
– Four Reversible Carbon Blades 18-20″
– Three Tractor Yokes available
– Recommended PTO HP: 35 min
– 180 HP Shear Pin w Greaseable Slide
$4,928.00$5,392.00
Out of stock
– Open Height 8′-6″; Knife Length 7′-4″; Lift cap. 2,500 lbs
– Max Bale Width 5′-7″ Max Bale Height 6′-0″
– Pivot Points Bronze bushings on knife point
– Hydraulic Cylinder 3.5″ Diameter x 20″ Stroke
– Required Hydraulics: One pair of auxiliary outlets
– 3-point hitch fits all category 2 tractors included
– Weight 680 lbs.; Not available until July 2012
$3,358.00
Out of stock
– Open Height 8′-6″; Knife Length 7′-4″; Lift cap. 2,500 lbs
– Max Bale Width 5′-7″ Max Bale Height 6′-0″
– Pivot Points Bronze bushings on knife point
– Hydraulic Cylinder 3.5″ Diameter x 20″ Stroke
– Required Hydraulics: One pair of auxiliary outlets
– Optional 3-point hitch fits all category 2 tractors
– Weight 680 lbs.
$3,200.00
– Category II & III hitch system
– 1/4″ thick X 24″ diameter. blade.
– 6 bolt 6″ bolt hub, circle rated for 4570 lbs.

,

discditcher2.jpg xa0 discditcher3.jpg
$2,513.00
Rockaway Companion Bucket for MDS2-8415SD Rockway Super Duty Rock Sifting Attachment.
$1,393.00
Out of stock
– 50 cc, 2.5 h.p. Tanaka two-stroke engine
– Solid steel drive shaft
– Heavy-duty, two-stage air filtration system
– Unique height adjustment system
– Stronger and longer throttle and height-adjustment wires
– Not available in California

,

,

4/12/12
$1,093.00
– Guide Lever Included
– Heavy Duty 90 H.P. Gearbox, Power Shaft w shear pin
– Gearbox Slip Clutch Optional
– 2″ round output shafts
– Augers secured by a collar and two 1/2″ bolts
– Augers Sold Separately, in 32″ or 44″ lengths to 36″ dia.

$1,083.00
– Moldboard is 3/16″ formed steel
– 3/16″ end plates.
– Scarifier shankxa0 3/4″ X 2″ high carbon steel.
– Cutting edges 9/32″ X 4″ high carbon steel
– 517 lbs
$893.00
– Moldboard is 3/16″ formed steel
– 3/16″ end plates.
– Scarifier shankxa0 3/4″ X 2″ high carbon steel.
– Cutting edges 9/32″ X 4″ high carbon steel
– 517 lbs
$793.00
– Scarifier shankxa0 3/4″ X 2″ high carbon steel.
– Approximate Capacity:15 CU.FT.
– No. Shank: 6 Each
– Main beam is 3″ Square Tubing.
– Moldboard is 3/16″ formed steel

– Cutting edgesxa0 9/32″ X 4″ high carbon steel
– 440 lbs

$753.00
– Approximate Capacity:13 CU.FT.
– No. Shank: 5 Each
– Main beam is 3″ Square Tubing.
– Moldboard is 3/16″ formed steel
– 3/16″ end formed steel plates.
– Scarifier shank of 3/4″ X 2″ high carbon steel.
– Cutting edges 9/32″ X 4″ high carbon steel
– 343 lbs
$633.00
– For Category 1 Hitches
– SE2 48 Solid Rear BLD
– Approximate Capacity:15 CU.FT.
– No. Shank: 6 Each
– Main beam is 3″ Square Tubing.
– Moldboard is 3/16″ formed steel
– 3/16″ end plates.
– 380 lbs
$583.00
– For Category 1 Hitches
– Approximate Capacity:12 CU.FT.
– No. Shank: 5 Each
– Main beam is 3″ Square Tubing.
– Moldboard 3/16″ formed steel
– 3/16″ end plates.
– Scarifier shank 3/4″ X 2″ high carbon steel.
– Cutting edges 9/32″ X 4″ high carbon steel
– 306 lbs
$493.00
– HANDEE II Box Blade w/4sh
– For Category 0 Hitches
– Approximate Capacity:10 CU.FT.
– No. Shank: 4 Each
– Main beam is 3″ Square Tubing.
– Moldboard 3/16″ formed steel & 3/16″ end plates.
– Scarifier shank 3/4″ X 2″ high carbon steel.
– Cutting edges 9/32″ X 4″ high carbon steel
– 267 lbs
$493.00

– Light Duty: for 6″ and 9″ dia.
– EC044 digs 44″ deep
– For Category 1 three-point
– 2-1/2″ steel pipe frame. No Guide Lever
– 2″ round output shaft
– Augers Sold Separately

$453.00
PFM-40000133 Ripper Shank Assembly
$415.00
Excellent in any soil condition.
– Helps reduce machine and blade wear with faster ground speed and increased ditch depth consistency.
– Long lead time on this item.
$320.00