EC-100-Cantherm-indirect-fired-heater.
EC-100-Cantherm-indirect-fired-heater.

Cantherm EC-Series Indirect Fired Portable Heaters or 2024-2025

Flat Rate Shipping (for immediate purchases) : $ 0
Use Quick Quote in the tab below for precise shipping.

100K, 200K, 300K BTU Models. The Cantherm EC Series of diesel indirect-fired portable heaters are the go-to heater for convenience and high heat output. Italian-made heaters distributed out of Winnepeg Canada ot the Canadian and North American markets. A full line of accessories — ducts, splitters, thermostats, remote fuel connectors are available. For larger models see the Cantherm PHOEN SERIES indirect-fired 400K BTU with two fans..

ORDER REVIEW REQUIREDManufacturer pricing, availability and shipping or freight must be confirmed before purchase. Add the product and options to your Review Cart. You will not be charged or committed to purchase. Equipmentland will confirm the final price and shipping cost before requesting payment.
SKU: CAN-EC-SERIES Categories: , , , , ,

Cantherm EC-Series Indirect Fired Oil Heaters and Accessories

  • EC Series Heaters:
    – Four loop heat exchanger, provides more efficiency
    – Built-in oil burner
    – Electronic flame control
    – Safety overheat thermostat and pressure switch
    – Double skinned combustion chamber
    – Pre-heated Oil filter (except EC100)
    – Two stage startup for cold starts
    – Pre-purge and post-ventilation cycles
    – Twist-lock tank cap with leash
    – Stainless steel heat exchanger
    – Pneumatic tires
    – Fuel Tank
    – Internal Thermostat
    – Fuel: Burns Diesel, Kerosene, Fuel Oil, JP-8, Jet A Fuel

MODELS AND SPECIFICATIONS

EC 100 Heater
– Heat Output: 113,000 BTU
– Air Flow: 880 CFM; Heat Rise 150 deg. F.
– Heat Output: 113,000 BTU
– Air Flow: 880 CFM; Heat Rise 150 deg. F.
– .81 GPH; 11.9 Gallon Tank; 110 V
– Pneumatic Tires, Fuel Gauge,
– Preheated fuel filter std.
– Uses 12″ x 12′ Pin-Lock Duct;
– No adapter needed
– Tank Capacity: 11.9 US Gallons
– Fuel Consumption: .81 Gallons/hour
– Size: 47″L x 18″W x 27″H
– Weight: 94 lbs

EC 200 Heater
– BTU: 219,000
– Field Consumption (GPH): 1.56
– CFM: 1530
– Duct Length (ft.): 50
– Dimensions (LxWxH in.): 47x20x37
– Weight: 176 lbs
– Duct Diameter (in.): 12
– Tank (gal.): 17.2
– Power Supply: 110V

EC 300 Heater
– BTU: 306,000
– Field Consumption (GPH): 2.18
– CFM: 2500
– Duct Length (ft.): 50
– Dimensions (LxWxH in.): 73x28x41
– Weight (lbs): 264
– Duct Diameter (in.): 16
– Tank (gal.): 27.7
– Power Supply: 110V

The EC Series is built using a proprietary four-loop exhaust system that results in higher efficiencies and heating power than the traditional three-loop system used in most heaters:

  • It comes standard with a four-loop heat-exchanger, providing a longer path for exhaust gases to release their heat before exiting through the chimney. The end result is a 2% increase in efficiency over the performance of the traditional three-loop heat-exchanger.
  • Hot gas passages between the EC Series firebox and exchanger are exposed to lower temperatures, pumping up the heater and gaining an additional 10% in heating power compared to three-loop units of the same size.
Weight N/A
Dimensions 20 × 37 in
Cantherm EC Heater Models

EC100, EC200, EC300
  • This field is for validation purposes and should be left unchanged.
  • Best Rates for commercial location WITHIN city limits; or a freight depot for will-call, a farm supply store, NAPA dealer, etc. You can change this later.